The Xantrex Freedom HF 1800 (806-1840) is a combined inverter/charger designed for boats, RVs, and trucks that need both AC power on the go (12V battery to 120V AC inverted output, 1800W continuous, 3600W peak surge) and a built-in 3-stage battery charger to top off the battery bank when shore power is connected. Modified sine wave output suitable for resistive and most motor loads (not pure sine wave – check sensitive electronics compatibility before relying on it). Two AC outlets, remote on/off capable, ignition lockout to minimize key-off battery drain, ETL certified to UL458 for mobile applications, automatic protection (over/under-voltage, over-temperature, overload, short-circuit, ground-fault). 18 x 9.5 x 4.2 inch chassis. Two-year limited warranty.
The Xantrex Freedom HF 1800 is a combined inverter/charger – one chassis that runs in two modes depending on whether shore power is available. With shore power present (boat plugged in at the dock, RV plugged in at a campground), the unit operates as a battery charger: takes the 120V AC shore input and delivers up to 40 amps of regulated DC current to charge a 12V battery bank using a three-stage charging profile. Without shore power (boat at anchor, RV boondocking, truck running on auxiliary battery), the unit operates as an inverter: takes 12V DC battery input and produces 120V AC output to run AC loads (1800 watts continuous, 3600 watts peak surge for short-duration motor startup loads). Two functions in one chassis – meaningfully simpler install than buying a separate inverter and a separate battery charger.
1800 watts continuous output. The 1800W continuous rating means the inverter can deliver 1800 watts of AC load indefinitely (limited only by battery capacity and the inverter’s heat dissipation, which the cooling fans handle). 1800W is enough for typical RV / boat loads: a microwave oven (most are 700-1200 watts), a coffee maker (800-1500 watts), a TV plus DVD player and a few small appliances simultaneously, a CPAP machine plus laptop charger plus phone chargers, a small toaster, a power tool. NOT enough for: a residential air conditioner (typically 1500-2200 watts steady plus 3000W+ startup spike), a hair dryer at full heat (1800W is borderline – works for low setting only), an electric kettle at full power (1500W is the limit). For higher-load applications, the larger Freedom HF 2000 or the pure sine wave Freedom XC variants are the right call.
3600 watts peak surge. The 3600W peak rating handles the brief startup current spike that motor loads draw when they first energize. Refrigerator compressors, well pumps, power tool motors, and microwave magnetron startup all draw 2-4x their steady-state current for fractions of a second at startup. The 3600W surge capacity (2x the continuous rating) lets the inverter handle these startup spikes without faulting out. Without sufficient surge capacity, motor loads either fail to start or trip the inverter’s overload protection on every startup attempt.
Modified sine wave output – what that means. The Freedom HF outputs modified sine wave AC (versus pure sine wave). Modified sine wave is a stepped square wave approximation of true sinusoidal AC – it has the right voltage and frequency, but the waveform shape isn’t perfectly sinusoidal. For most loads, this doesn’t matter: resistive loads (toasters, electric kettles, incandescent bulbs, electric blankets) run identically on either waveform. Most motor loads (refrigerator compressors, microwave fans, power tools) run fine on modified sine. The exceptions where modified sine wave causes problems: some sensitive electronics may exhibit audio buzzing or screen flickering on modified sine, some medical devices (CPAP machines especially – check the manufacturer’s specifications) require pure sine, and laser printers / some battery chargers don’t tolerate modified sine waveform. If you’re powering sensitive electronics, the Xantrex pure sine wave Freedom XC variant is the right call instead.
40-amp three-stage battery charger built in. When shore power is connected, the unit operates as a 40A 12V battery charger using a three-stage charging profile: bulk charge (high current, fast charge to 80% state of charge), absorption (lower current, completes the top 20% of charge without overheating the battery), and float (maintenance level current, holds the battery at full charge indefinitely without overcharge damage). The three-stage profile is the modern standard for proper battery health – meaningfully better than older single-stage chargers that hold the battery at constant voltage and slowly cook the electrolyte over time. The 40A charge rate is appropriate for typical 100-200Ah battery banks (charge rate should be 10-20% of bank capacity for proper charging). For larger banks, the charging takes longer but still works.
Ignition lockout to minimize key-off battery drain. The ignition lockout feature wires the inverter’s enable signal to the vehicle’s ignition switch (or to a manually-operated switch on a boat). When ignition is OFF, the inverter is fully disabled (zero AC output and minimal standby current draw – typically under 1A). When ignition is ON, the inverter is active. The lockout prevents the inverter from accidentally drawing the battery down overnight if you leave it ON when you intend it OFF, and prevents the inverter’s standby losses from depleting the battery during long-term storage.
Two AC outlets on the front panel. The unit has two standard NEMA 5-15R AC outlets (the standard residential outlet) on the front panel – plug AC loads directly into the outlets without needing additional wiring. For installations that need hardwired AC distribution (a sub-panel feeding multiple AC outlets throughout the boat / RV), the unit also has a hardwired AC output terminal block, so you can wire the inverter into a marine AC sub-panel that distributes through the hull / coach.
Quick-connect AC terminal blocks. Both AC input (shore power) and AC output (hardwired distribution) use quick-connect terminal blocks rather than traditional screw terminals – faster install, lower risk of loose-connection arcing over time, and easier to remove for maintenance.
87% efficiency. The Freedom HF runs at roughly 87% efficiency in inverter mode, meaning roughly 13% of the input DC power is lost as heat during the inverter’s switching cycle. For an 1800W output, that’s roughly 270W of heat the cooling fans must dissipate. Plan the install location to provide adequate ventilation – the unit needs at least 4 inches of clearance on all sides for the cooling fans to work effectively.
ETL certified to UL458. The unit carries the ETL certification mark for compliance with UL458 (the Underwriters Laboratories standard for marine and mobile inverters). The certification means the unit has been tested for the safety hazards specific to mobile installations: vibration tolerance, salt-fog resistance, electrical isolation, fire safety. ETL UL458 certification is required by some marine insurance policies and by many marina shore power codes.
What’s NOT included. Battery cables (sold separately – the right battery cable size depends on the cable run length, the typical 12V 1800W install needs 4 AWG or larger cable). DC fuse / breaker (sold separately – typical install uses a 200A T-class fuse on the positive battery lead near the battery). Remote on/off panel (sold separately – the unit is remote-capable but the actual remote panel is a separate purchase).
Install. Mount the chassis on a flat surface in a well-ventilated location near the battery bank. Connect 12V battery cables (positive through the fuse, negative direct to battery negative) using 4 AWG or larger cable for the 1800W rating. Connect 120V AC shore input to the AC IN terminal block (hot, neutral, ground per shore wiring). Connect 120V AC distribution to the AC OUT terminal block (or use the front panel outlets directly). Connect the ignition lockout wire to the vehicle ignition / boat keyswitch. Two-year limited warranty applies.
